Admin: /* Memory Configuration */

2025-05-20T12:23:41Z

Memory Configuration

Admin at 12:23, 20 May 2025

2025-05-20T12:23:07Z

Admin at 14:00, 21 July 2019

2019-07-21T14:00:56Z

Admin: /* Firmware */

2019-07-07T21:16:16Z

Firmware

Admin at 19:47, 7 July 2019

2019-07-07T19:47:43Z

New page

[[File:Cyrus_plus_board.jpg|thumb|250px|A-EON Technology Cyrus motherboard]]

== Introduction ==

This page provides information repository about the X5000 computer from A-EON Technology Ltd.

== Motherboard Variants ==

The X5000's CPU features a 64-bit PowerPC e5500 Architecture-based microprocessor core from Freescale Semiconductor.

It has two main variants of motherboard:

* X5000/020 with [http://en.wikipedia.org/wiki/QorIQ#P5 P5020 Dual Core CPU] running at a clockspeed of 2Ghz
* X5000/040 with [http://en.wikipedia.org/wiki/QorIQ#P5 P5040 Rev C Quad Core CPU] running at a clockspeed of 2.2Ghz

== Motherboard Connectors ==

Back panel from left to right:
* serial RS-232
* ethernet RJ-45 10/100/1000 mbps
* 2x USB 2.0 type A female
* 2x USB 2.0 type A female
* 2x USB 2.0 type A female

On board:
* 2x USB 2.0 header
* SATA 0
* SATA 1
* DIMM 0 DDR3
* DIMM 1 DDR3
* micro SD card ROM
* CR2032 battery for real time clock
* PCI-E x16 slot
* PCI-E x4
* PCI-E x1 / Xorro
* PCI-E x1
* PCI-E x1
* PCI 5v 32-bit 33Mhz
* PCI 5v 32-bit 33Mhz
* Haze Xorro Header

== Memory Configuration ==

* X5000/20 requires a minimum specification of DDR3 1333Mhz standard 1.5v DIMM
* X5000/40 requires a minimum specification of DDR3 1600Mhz standard 1.5v DIMM

It is recommended to use DIMMs in matched pairs. The total physical maximum size of memory that the memory controllers can address is 64GB, however the practical memory size limit will depend on software.

{| class="wikitable"
|+ Memory Compatibility
|-
! size
! speed
! manufacturer
! part number
! X5000/20
! X5000/40
|-
| 2GB
| 1333Mhz
| Corsair
| VS2GB1333D3
| Yes
| No
|-
| 4GB
| 1600Mhz
| Kingston
| HX316C10F/A
| Yes
| Yes
|-
| 4GB
| 1600Mhz
| Kingston
| HX316C10FW/4
| Yes
| Yes
|}

== Hardware Revision History ==

* Version 1.0: micro-ATX form factor produced in early 2012
* Version 2.0: full ATX form factor produced in early 2013
* Version 2.1: full ATX form factor supplied to beta testers in 2014-15
* Version 2.2: full ATX form factor consumer release produced in 2015

The revision number is written on the X5000's Cyrus motherboard above the DIMM memory slot.

== Firmware ==

The X5000 uses a 4GB micro SD card as it's ROM. This contains the system's firmware and is removable for reflashing. The card does not have a filesystem so only RAW data maybe copied to it.

The system uses a modified Uboot firmware which includes a graphical front end that is displayed if the user presses the Escape key on system startup.

[[AmigaOne_X5000_Update_Uboot|Click here]] for a guide to writing your firmware from OS4 and Uboot.

{| class="wikitable"
|+ Removal of the X5000's micro SD card ROM
|-
! Description
! Picture
|-
|The ROM is installed on the X5000 motherboard as shown
''select thumbnail image on the right for larger view''
|[[File:x5000_rom_1.jpg|160px]]
|-
|Gently push back on the metal clip in the direction of memory slots as shown
''select thumbnail image on the right for larger view''

'''Important: before performing this operation ensure you are electrostatically discharged'''
|[[File:x5000_rom_2.jpg|160px]]
|-
|Once the metal clip is fully pushed back, it will release and rotate upwards
''select thumbnail image on the right for larger view''
|[[File:x5000_rom_3.jpg|160px]]
|-
|Once the metal clip is fully pushed back, it will release and rotate upwards
''select thumbnail image on the right for larger view''
|[[File:x5000_rom_4.jpg|160px]]
|-
|The micro SD card can then be removed from the socket
''select thumbnail image on the right for larger view''
|[[File:x5000_rom_5.jpg|160px]]
|}

'''Restoring the MAC addresses after flashing firmware'''

To reset your ethernet MAC addresses correctly after a firmware update, perform the following steps:

1. Whilst the animated ball title screen is being played, press the '''ESC''' key to display the '''Early StartUp Control''' menu

2. Select the '''Command Line''' option or press the '''m''' shortcut key

3. At the '''X5000>''' prompt enter the following (pressing enter after each line):

<pre style="color: black; background:lightgray; font-family:courier; width:50%">
setenv ethaddr
setenv eth1addr
setenv eth2addr
saveenv
</pre>

4. Once this is saved, reset the system. This will now force the motherboard to retrieve the correct MAC addresses and record them.

All future firmware updates have empty MAC addresses so this process can be performed to retrieve the correct values.

=== Additional UBoot Options ===

The new Uboot includes the options to reduce or eliminate the rotating ball animation. Additionally it also includes a special default time-out option.

Three new environment firmware variables are included:

'''amigabootmenu_animate''' default 1: Set to 0 to disable the boot animation. Set to 1 to enable the animation.

'''amigabootmenu_animcycles''' default 10: Specifies how many times the animation should be played before the default boot selection is booted. Only has an effect if amigabootmenu_animate is set to 1.

'''amigabootmenu_timeout''' default 0: If set to a non-zero value, it specifies how many seconds should elapse before the deafult boot selection is booted. This mechanism overrides amigabootmenu_animcycles, so if both are set, this one takes preference.

The result is the boot-up time can be greatly reduced. e.g. ~30+ seconds from power-up to Workbench if '''amigabootmenu_animcycles=1''' and '''amigaboot_quiet=y'''

== Motherboard LED Status ==

{| class="wikitable"
|+ LED Information
|-
! label
! colour
! description
|-
| style="text-align:center;" | LED1
| style="color: white; background-color: green; text-align:center;" | green
| standby power indicator
|-
| style="text-align:center;" | LED3
| style="color: white; background-color: red; text-align:center;" | red
| CPU Platform voltage power good (CPLD controlled)
|-
| style="text-align:center;" | LED4
| style="color: white; background-color: red; text-align:center;" | red
| CPU Core A voltage power good (CPLD controlled)
|-
| style="text-align:center;" | LED13
| style="color: white; background-color: red; text-align:center;" | red
| CPU Core B voltage power good (CPLD controlled)
|-
| style="text-align:center;" | LED14
| style="color: white; background-color: red; text-align:center;" | red
| DDR 3 voltages power good (CPLD controlled)
|-
| style="text-align:center;" | LED15
| style="color: white; background-color: red; text-align:center;" | red
| IO voltages power good (CPLD controlled)
|-
| style="text-align:center;" | LED5
| style="color: white; background-color: red; text-align:center;" | red
| PORESET state indicator (CPLD controlled)
|-
| style="text-align:center;" | LED6
| style="color: white; background-color: red; text-align:center;" | red
| HRESET state indicator(CPLD controlled)
|-
| style="text-align:center;" | LED7
| style="color: white; background-color: red; text-align:center;" | red
| ASEELP state indicator (CPLD controlled)
|-
| style="text-align:center;" | LED16
| style="color: white; background-color: red; text-align:center;" | red
| STANDBY state indicator (CPLD controlled)
|-
| style="text-align:center;" | LED8
| style="color: white; background-color: red; text-align:center;" | red
| MCU temperature warning LED
|-
| style="text-align:center;" | LED9
| style="color: white; background-color: red; text-align:center;" | red
| MCU error LED
|}

== Technical Reference Manual ==

The official Technical Reference Manual can be downloaded from the AmiSphere server (an AmiSphere account is required)

[https://www.amisphere.com/download/trm_cyrus_1-1-1_AEON.pdf Technical Reference Manual v1.1.1 PDF]

Note: this copyrighted document should not be distributed on any other website

== Trivia ==

There is a long running tradition, started originally by Commodore engineers, on having [http://en.wikipedia.org/wiki/The_B-52%27s The B-52s] song titles on Amiga compatible hardware. The X5000 motherboard is no exception to this tradition as it features '''Breezin'''' on the silkscreen.

The motherboard is codenamed '''Cyrus''' in homage to the character Cyrus Smith (named Cyrus Harding in some English translations) who is one of the protagonists of Jules Verne's novel The Mysterious Island.

← Older revision		Revision as of 14:00, 21 July 2019
Line 244:		Line 244:

	Note: this copyrighted document should not be distributed on any other website		Note: this copyrighted document should not be distributed on any other website
		+
		+	== Emergency USB Flash Drive ==
		+
		+	Some suppliers may offer and supply a complimentary [[X5000 Emergency Boot USB]] with the X5000 system. The USB flash drive is designed to make it easy for a user to boot their [[X5000]] and setup/restore a hard drive without the frustrations of manually copying across files from different locations.

	== Trivia ==		== Trivia ==

@@ Line 92: / Line 92: @@
 | Yes
 |}
 == Hardware Revision History ==

@@ Line 69: / Line 69: @@
 | Yes
 | No
 |-
 | 4GB

@@ Line 101: / Line 101: @@
 The X5000 uses a 4GB micro SD card as it's ROM.  This contains the system's firmware and is removable for reflashing.  The card does not have a filesystem so only RAW data maybe copied to it.
-The system uses a modified Uboot firmware which includes a graphical front end that is displayed if the user presses the Escape key on system startup.
+The system uses a modified Uboot firmware which includes a graphical front end that is displayed if the user presses the Escape key on system startup.  The firmware is developed and distributed by A-EON Technology.
 [[AmigaOne_X5000_Update_Uboot|Click here]] for a guide to writing your firmware from OS4 and Uboot.

X5000 - Revision history

Admin: /* Memory Configuration */

Admin at 12:23, 20 May 2025

Admin at 14:00, 21 July 2019

Admin: /* Firmware */

Admin at 19:47, 7 July 2019